![1960s and 70s ford engine codes 1960s and 70s ford engine codes](http://classiccardb.com/uploads/postfotos/1960-ford-starliner-galaxie-2-door-hardtop-352-x-code-ratrod-custom-hotrod-7.jpg)
The original 1985 brake system utilized an 10" front rotor while the 1987 system is 11" increasing the swept surface area of the brakes. The front brake system currently on the car is from a 1987 Mustang. An example is my 1985 Mustang in American Sedan, generally I can use any bolt on component from 1979 through 1993 Capri or Mustang. In other words use a older or newer part from that product line of car. In SCCA Solo and Club Racing the rules often allow updating/backdating parts. Often friends will call me trying to determine Ford parts they can use or substitute. For example - "A" is for a 289/302 motor, whereas a "C" is for a 351C, 4v motor.
![1960s and 70s ford engine codes 1960s and 70s ford engine codes](https://i.pinimg.com/originals/3e/e4/f6/3ee4f64295da85ee52c04ca6e89aa181.jpg)
![1960s and 70s ford engine codes 1960s and 70s ford engine codes](http://www.drivinithome.com/wp-content/blogs.dir/3/files/2012/02/0-66-16-13.jpg)
This indicates what application the basic part is used for. This is the number that identifies what the part actually is - 2062 is a front slave cylinder, or 6268 is a timing chain set.
1960S AND 70S FORD ENGINE CODES MANUAL
Z - Ford Service Part - This came from the Engineering DepartmentĢ140 - Basic part number - 2140 is a master cylinderĬR - Design Change - indicates manual disc brakes Casting Code Definitions Example for Illustrative PurposesĬ - Decade of Manufacture - 1960's in this case They all are master cylinders however, and share a basic part number.
![1960s and 70s ford engine codes 1960s and 70s ford engine codes](https://image.invaluable.com/housePhotos/ejsauction/41/678741/H8897-L217847438_original.jpg)
An example could be a master cylinder - most master cylinders have a basic part number of 2140, but there a number of different master cylinders for different Ford vehicles. Ford is famous for using parts designed for one car on a variety of models.Ī basic part number is included within the casting number and indicates what the part is, not what it was made for, or when it was made. Many Mustang parts were originally designed for the Falcon and carry a Falcon casting number. Just because a part was originally made for a Falcon doesn't mean the part came off of a Falcon. People are often confused by looking at a part or casting number. These numbers tell you what that part was originally designed for, what department designed it, and when it was designed. Many parts are too small to have the number cast or printed on it, but it still has a casting number. Those are those big long codes (C7ZZ-6540544-DR, etc) that you find that identify every Ford part made. You can look up this code online to see the specs of your current engine.Part numbers and casting numbers are pretty much the same when it comes to "hard parts". Engine Code Number: This final 3-digit number is the ID of your particular engine.(assuming the year code is for the 70's). 0-A would mean January 1970, 5-C March 1975, etc. There is no "i" so people don't confuse it the number 1. The months are in alphabetical order, so A = January and M = December. Month Built: This hyphenated number and letter correspond to the month.70, for example, would mean it was made in 1970. Year: The next two numbers are for the year the engine was built."C" is for Cleveland, "E" is for Ensite, Canada, and "W" is for Windsor, Canada. Manufacturing Plant: The single letter to the right of the CID is where the engine was built.Cubic Inch Displacement (CID): The first three numbers, found in the upper left corner, tell you the size of the engine.From upper left to bottom right: X Research source Luckily, the tags are simple to breakdown.
1960S AND 70S FORD ENGINE CODES HOW TO
Once you've found the identification tag, you need to know how to read it to get the right information.